For several years I’ve used a Raspberry Pi Zero for sensors, camera & door motor control which opens & closes a chicken coop door. The Rpi & controller is 5v, the motor is 12v. This has been powered by around 50’ of extension cord, but the elements are beginning to weather the cord & we also need to move the chickens further away from our mains. I think it is time to implement solar. I aspire to assemble a PV, battery, & converter system which:
- Uses an off-the-shelf 12v PV panel (30w or so)
- Uses LiFePO cells for heat resiliency & stability
- Provides both 12v & 5v power
- Isn’t proprietary; uses standard, easily-sourced components… unless it meets specs perfectly & isn’t terribly expensive.
- Minimal power draw; at most 2 amps @ 12v for 10 seconds twice daily.
Does anyone have suggestions regarding this configuration, know of a post, blog, or video which does something similar, or is willing to ID components you’d recommend for this project?
You must log in or register to comment.
30w might not be sufficient to run the pi with a camera, etc., especially taking into account cloudy days and whatnot. Do you live somewhere particularly sunny?
I’d start off with a single 100w panel at a minimum. That’s what I have, and in the winter (right now) it maxes out at around 45 watts, and only for a couple hours a day. The rest of the day it’s a trickle.
Does the Pi need to be on 24/7? Certain charge controllers allow you to implement a schedule for the “load” terminals. You’ll want something like this to run the Rpi.
Does it get below freezing where you are? LiFePO4 get damaged if you charge them below freezing. In that case a deep-discharge rated Lead Acid battery might be better.
I just built out a solar setup for my shed. It has different needs than yours, but I’ll be running a Pi 3B+ 24/7 and I think my setup should handle that ok, even in the winter months.
A 100w panel should be about $100-120USD. I recommend a nice solar charge controller – something like the Victron SmartSolar 100/20 at a minimum (100/30 would be better for adding another panel or 2 in the future). Watch some YouTube on why Victron is great, especially if you’re a nerd and want to check the status of stuff from your house via bluetooth.
For a panel, charger, and battery, you’re in the $400 range. Try and use some spare wire you have laying around – 12 gauge should be fine. If you go cheaper and get a 30w panel and a cheapo charge controller from AliExpress (nothing wrong with that, just fewer features), you might end up spending more in the future if it’s not sufficient.
Thanks for the reply. Do you have stats on how many watt hours you collect from the 100w panel in the Dec/Jan (assuming you’re in the northern hemisphere), and how those stats vary on overcast days vs sunny? I’m around 37°n and relatively sunny in the winter, except for a gloomy week here or there - an adequate battery buffer will be needed for those days, and the capacity can be shifted to ventilation fans in the summer.
While it does freeze here (occasionally down to 0° F) the battery will be inside the chicken coop where the temp has always remained above freezing. Initially my concern with lead acid was the risk of gassing into the birds’ airspace, which is why I’m drawn to the LiFePO4 chemistry. Victron does seem great for heavier(medium)-duty scenarios like sheds or RVs.
The pi is a zero, which pulls about 25-33% the current of a 3b, and I’ve been able to run it off a 10,000 mah battery bank for over 24 hours. It is beneficial to have it running continuously during daylight hours only, aside from logging weather lows, but I can’t think of a practical method to shut it down & bring it online automatically - at that point it’d probably make more sense to switch to an ESP32 device feeding data to a primary server inside the house.
I’m around 41°N (southern New England). I installed a Victron SmartSolar 30A just within the past week, so the stats I have are limited. The best I’ve seen so far was yesterday where I got 50Wh. Most other days it has been 40Wh. Today is a bit cloudy so I’ll try and update you on what I get.
Edit: I made a spreadsheet to sort of figure out what I can accomplish with 50Wh – and it’s not much! If the Pi draws 2.5 watts, the solar will only cover 20 hours not including any other electricity I want to use.
This time of year has the shortest days, so if I can bump it to 60+ Wh a day that will be better. My property also has the downside of a hill to the west, so it makes direct sunlight even shorter. I’ve already ordered a 2nd 100w panel from Harbor Freight so that will help.
Do you have stats on how many watt hours you collect from the 100w panel in the Dec/Jan (assuming you’re in the northern hemisphere),
You can model average insolation (and use that to extrapolate average harvest) by month using tools like PVwatts. Here’s a walkthrough.
Using Bowling Green, KY as an example since it’s on the 37th. 100w of flatmounted panel on an MPPT solar charge controller would average:
Solar wattage 100 Month Daily Wh Avg Jan 168 Feb 249 Mar 331 Apr 426 May 513 Jun 598 Jul 555 Aug 506 Sep 396 Oct 305 Nov 201 Dec 156 Average 367Derate those yields by ~18% if using PWM. <-- rule of thumb, not gospel
if we are on the west coast instead, here’s Santa Cruz, California:
Solar wattage 100 Month Daily Wh Avg Jan 206 Feb 286 Mar 386 Apr 519 May 582 Jun 642 Jul 605 Aug 542 Sep 447 Oct 349 Nov 245 Dec 183 Average 416and how those stats vary on overcast days vs sunny?
The figures above are daily averages, including normal weather patterns and are how we size our systems. But for the sake of curiosity/understanding, my observations have been that if my clear-day harvest is X then overcast is 0.6X, bright overcast is 0.7X and dark/rainy is 0.05-0.10X. Cloud-edge effect and other reflective phenomena can result in harvest >1X.
While it does freeze here (occasionally down to 0° F) the battery will be inside the chicken coop where the temp has always remained above freezing.
A battery warming solution could be implemented for $20 (warming pads, 12v temp controller).
Not OP but this is really neat. Thanks.
Over the past few days my system has been severely under performing in relation to these calculations. For January it says 290 Wh per day, but I’m only seeing 50. I do have a lot of trees, so probably some shading… maybe even a lot of shading.
Jan 290.3 Feb 392.9 Mar 387.1 Apr 400.0 May 387.1 Jun 400.0 Jul 419.4 Aug 387.1 Sep 400.0 Oct 322.6 Nov 300.0 Dec 290.3
