This might be a better angle.

We stand on the sholders of giants.

It’s always good to give back to the community and open source it

I can’t imagine how’d you’d link them up, without having to reach inside the case, and having it modular.

Ideally the zig zag isn’t there, but did you see the before?

I have basically taken a power strip, and made each plug a module.

The inside of a power strip, like in this image, is in series.

mains → yellow → red → blue → green → blue(end)

If a join between yellow and red is broken, it knocks out red and everything after it.

If what is plugged into yellow is plugged out, or disconnects everything else keeps working.

The same is true for my setup, the joins between Yellow, red etc. are just on the outside of the case, so you can disconnect them if you want, which would kill the power to what is after it. But you don’t have to do that.

You’re explaining scenarios where you incorrectly use my setup.

You can wire the switches so that if switched off it only kills power to that server and nothing else in the chain. You then basically have this, but modular:

Yea if you rip out a cord that you shouldn’t you’re going to lose power, that is true of any power strip.

This has more components, so more things can fail, I will give you that, but that’s unlikely and for me at least, worth the trade off in making it modular.

If the above picture was powering your servers, and you wanted to add a 7th plug, you’d have to unplug everything and buy a power adapter with more sockets, and deal with the rats nest of cables that follows, or add another of these that might have the same problem in the future.

Very nice, is that a KWS rack?

I don’t think that existed yet when I started my journey, they seem very solid.

I went for aluminum for max strength and didn’t trust 3D printed parts for strength, but after getting a printer, I see you can print fold out chairs that you can stand on, so they can be more than strong enough.

I don’t think I understand your question.

If you plug all your servers into a power strip like this, all the power goes through the power strip and through one cable. If there is a fault in the power strip, all the servers will lose power as a fuse will trip.

The same is true for my setup, I have added no new failure modes.

The name has been in my family far longer than that program has existed, so the way I see it, if anything, they are copying me xD

Thanks for this, I founds some self-extinguishing PETG, that’s really not much more expensive than PETG. Definitely worth the money

https://shop.filament-pm.com/petg-frjet-self-extinguishing-white-1-75-mm-0-5-kg/p166

Uggg don’t give me ideas, I’ve already sunk way too much time into designing this 😅️🤣

So you could just put a relay between my power-module and your server, and it’s problem solved.

A redesign to incorporate one of these would be great, there are also variants that monitor power draw, so you’d be able to see each servers power usage and switch it on or off remotely.

Why are you doing this to me?

My setup is as resilient as this would be:

I haven’t added any failure-modes

There are more duckies, a lil giraffe and a turtle at the front

Yea I realised that is a limitation, but Eh I’d take that trade-off for the modularity and good looking backside.

It’s rare that you add/remove things, and technically you can just plug out the inside and only that server will go offline with the rest keeping power.

My surname is Erasmus

Sure but then there should be some kind of onboarding, or a better default page.

New users might lose interest before finding communities they would have liked

I want it to be modular, so if I add another 2 servers, I can just add the server module in front, and its power module at the back.

Nice thanks!! You can get a 3D printer for fairly cheap to get started, the one I have is only 280 Euro now with 4 spools of filament

Nice thanks, that sounds good. I’d definitely only want to push to one place, if it then syncs to GitHub that’s fine.

Thanks yea I’ve used Codeberg before, but the main reason I use GitHub, is I try to create a good looking profile to point potential new Clients to when I’m looking for a new job, explaining Codeberg to them I feel is a step too much, and my income is Priority Nr1.

I’ll fight the Open-Source, anti-Big-Tech fight elsewhere.

Sure thing, there’s lots more details on my GitHub Write-Up including how to wire it up etc.